0 items in your basket
Total £ 0.00 EX VAT
Multi Process Welders
MIG Torches
TIG Torches
Welding Helmets
Welding Gloves & Clothing
MMA Electrodes
MIG Wire
Shop 55,000 Products
SERVICEDEPT.
RAPID BLOG
FEEDBACK
HIRE
WELD AND CLEAN WITH ONE TIG MACHINE.
Minarc T 223 ACDC GM is a new 220 A single-phase AC/DC TIG welding machine with built-in electrolytic weld cleaning capability. This portable multi-voltage welding machine allows you to perform high-quality TIG welding and professional weld cleaning with one machine.
Take the Minarc T 223 ACDC GM anywhere on-site and save time by completing and finishing perfect welds in one spot. The new MAX WeldClean electrolytic cleaning process is simple and easy to use. It just takes a moment to convert your TIG torch to cleaning mode, where an efficient combination of electric current and phosphoric acid offers quick removal of oxidation and discolouration around the weld, delivering immaculate welds.
Powerful and versatile, the Minarc T 223 ACDC GM TIG welding machine has important features like the Auto Pulse function, AC frequency control, memory channels, and convenient remote control options. A large colour display with impact protection and a clear user interface makes choosing settings in a wide range of light conditions easy.
Portable and lightweight
Its portable size makes Minarc T 223 ACDC GM easy to carry. Take it anywhere on-site for a convenient combination of powerful welding performance and easy-to-use electrolytic cleaning.
Powerful welding performance
Minarc T 223 ACDC GM is a professional TIG welder with high-quality welding performance and easy-to-use controls. It offers AC and DC TIG welding for working on a wider range of metals and thicknesses.
Weld and clean with one machine
MAX WeldClean lets you complete high-quality welds without using a separate weld cleaning machine. Save time and money by quickly activating cleaning mode for a powerful electrolytic weld cleaning process right after completing a weld. Post-processing the welds has never been so fast!
Fast and accurate control
A large, clear, and bright colour LCD display is easy to see in different work environments, and an intuitive control knob combined with simple on-screen process selection makes welding easier.
Kemppi Genuine Earth Cable 35mm² x 5m
Kemppi FR41 Foot Remote Control, for Minarc T
Kemppi Flexlite TX K5 225G Air Cooled 220 Amp Tig Torch, with 70° Angle Neck - 4m, 7 Pin
Kemppi 3 Year Global Parts & Labour Warranty
A buyer's guide to the kinds of welding, cutting and protective equipment people look at most, and what to check before choosing.
Duty cycle is the share of a ten-minute period that a machine can run at a stated output before it must cool down, usually quoted at a set ambient temperature. A machine may be rated at a higher duty cycle at lower output and a lower one at full output, so the figure only means something alongside the current it applies to.If the thermal protection cuts in, leave the machine running its fan and wait for it to reset. When comparing machines, look at the duty cycle at the current you will actually use, not just the headline maximum, and check the data plate and manual.
Most air plasma cutters need clean, dry, oil-free compressed air, and some have a built-in compressor. Moisture and oil in the air shorten the life of the torch consumables and spoil the cut.Check the maker's stated pressure and air flow, and make sure your compressor can keep up with continuous cutting, since a small compressor may not. A filter and water trap in the air line are normally needed, and a dryer helps in damp conditions. Remember to drain the trap and replace filters as the maker advises.
Look at the machine's data plate and manual for the supply voltage, the effective and maximum current it draws and the fuse or breaker size it recommends. Then check that the socket, cable and circuit protection at your workshop suit those figures.Do not assume that a plug fitting means the circuit can cope. If you plan to run the machine from a generator, check the maker's guidance on generator output and voltage quality. Have a competent electrician check the circuit if you are unsure.
Welding gloves are made in different types. Some give higher heat and wear protection with less feel and are for general welding and cutting. Others give better dexterity with lower protection, and these are generally recommended for TIG welding where fine control matters.Check the marking and the maker's description of what the glove is intended for, because a heavy-duty glove may not be intended for TIG. Also consider cuff length, lining and fit, and replace gloves that are worn, thin or burnt through.
